Silicon Laboratories Weather Radio si85xx User Manual

Si85xx-TB UG  
Si85XX UNIDIRECTIONAL AC CURRENT SENSOR TARGET BOARD USER  
S
GUIDE  
The Si85xx products are unidirectional ac current sensors available with full scale current sense input ranges of 5,  
10, and 20 A. Si85xx products are ideal upgrades for older current-sensing technologies offering size, performance  
and cost advantages over current transformers, Hall Effect devices, DCR circuits, and other approaches. The  
Si85xx are extremely low-loss, adding less than 1.3 mof series resistance and less than 2 nH series inductance  
in the sensing path at 25 ºC. Current-sensing terminals are isolated from the other package pins to a maximum  
voltage of 1,000 VDC.  
1. Kit Contents  
The Si85xx Unidirectional AC Current Sensor Development Kit contains the following items:  
10 Amp Si8512 based evaluation board  
Si85xx Unidirectional AC Current Sensor Target Board User's Guide (this document)  
2. Hardware Overview  
The Si85xx Target Board (Si85xx-TB, see Figure 1) provides a means to evaluate the ac current sensor in an  
existing application. It is meant to be soldered directly into the users existing power supply. The board comes with  
the Si8512 installed and provides a 10 Amp full scale input sense range and a 2.0 V full scale output voltage. For  
more details on the Si8512, refer to the Si85xx Data Sheet.  
Figure 1. Si85xx-TB Overview  
Rev. 0.1 6/07  
Copyright © 2007 by Silicon Laboratories  
Si85xx-TB UG  
 
 
Si85xx-TB UG  
4. Si85xx Evaluation Board  
The Si85xx-TB has a Si8512 installed. Refer to Figure 4 for the locations of the various I/O connectors and major  
components.  
J1  
J2  
J3  
J4  
J5  
J6  
J7  
5 V Supply Input power connection 5 V, 100 mA  
GND, Input Supply power return connection, 0 V  
HDR-2X2, Mode Control input  
HDR-2X07, R1, R2, R3, R4 inputs, OUT1, OUT2 outputs, and seven GND return pins  
IIN Positive Current Sense Input  
IOUT Negative/return Current Sense Input  
HEADER, TRST timing select jumper, default tied to VDD  
Figure 4. Si85xx-TB Layout  
4.1. VIN (J1, J2)  
The user-provided power supply should be connected to connectors J1 and J2 where J2 is the reference. The  
power source must be 5 V with at least 100 mA maximum output current.  
Table 1. J1, J2 Pin Descriptions  
Jumper #  
Description  
5 V, 100 mA  
GND  
J1  
J2  
4.2. Mode Pin (J3)  
Connector J3 is the Mode Control header. The user should tie this pin to either VDD or GND depending on their  
power supply.  
Table 2. J3 Pin Descriptions  
Jumper #  
Description  
J3  
VDD or GND  
Confidential Rev. 0.1  
3
 
 
Si85xx-TB UG  
4.3. R1, R2, R3, R4 Inputs, OUT1, OUT2 Outputs (J4)  
Connector J4 is used to provide the control inputs (R1, R2, R3, R4, MODE) to the Si85xx. It also provides the  
output voltage of the sensed input current on OUT1 and OUT2.  
Table 3. J4 Pin Descriptions  
Jumper #  
Description  
J4  
R1, R2, R3, R4, OUT1, OUT2, GND  
4.4. IIN (J5)  
Connector J5 is used to provide the positive current sense input to the Si85xx device.  
Table 4. J5 Pin Descriptions  
Jumper #  
Description  
J5  
IIN  
4.5. IOUT (J6)  
Connector J6 is used to provide the negative/return current sense input to the Si85xx device.  
Table 5. J6 Pin Descriptions  
Jumper #  
Description  
J6  
IOUT  
4.6. TRST RESET (J7)  
Connector J7 is used to set the timing for the Si85xx's integrator. J7 defaults to Reset option 1 where TRST is tied  
VDD providing approximately 200 ns of reset time. Reset option 2 is selected by connecting a timing resistor (R1 in  
Figure 4) from the TRST input to ground.  
Table 6. J7 Pin Descriptions  
Jumper #  
Description  
J7  
TRST – VDD or R1 to GND  
4
Confidential Rev. 0.1  
 
Si85xx-TB UG  
5. Schematic  
D
G N  
8
7
D
V D  
1 1  
1 2  
E D M O  
T S T R  
2
1
Confidential Rev. 0.1  
5
 
Si85xx-TB UG  
6. Bill of Materials  
Table 7. Si825x Multi-Phase POL Reference Design Bill of Materials  
Item  
1
Quantity  
Reference  
Part Number  
PCC2182CT-ND  
PCC1812CT-ND  
2551-2-00-44-00-00-07-0  
2551-2-00-44-00-00-07-0  
S2012-02-ND  
Manufacturer  
Digi-Key  
Digi-Key  
Bisco  
Description  
10 uF  
1
1
1
1
1
1
1
1
1
1
1
C1  
C2  
J1  
J2  
J3  
J4  
J5  
J6  
J7  
R1  
U1  
2
0.1 uF  
5 V  
3
4
Bisco  
GND  
5
Digi-Key  
Digi-Key  
Bisco  
HDR-2X2  
HDR-2X07  
IIN  
6
S2012-07-ND  
7
2551-2-00-44-00-00-07-0  
2551-2-00-44-00-00-07-0  
S1012-02-ND  
8
Bisco  
IIOUT  
9
Digi-Key  
Digi-Key  
Digi-Key  
HEADER  
DNP  
10  
11  
P150CCT-ND  
Si8512-IS  
Si851x  
6
Confidential Rev. 0.1  
 
Si85xx-TB UG  
NOTES:  
Confidential Rev. 0.1  
7
 
Si85xx-TB UG  
CONTACT INFORMATION  
Silicon Laboratories Inc.  
400 West Cesar Chavez  
Austin, TX 78701  
Tel: 1+(512) 416-8500  
Fax: 1+(512) 416-9669  
Toll Free: 1+(877) 444-3032  
The information in this document is believed to be accurate in all respects at the time of publication but is subject to change without notice.  
Silicon Laboratories assumes no responsibility for errors and omissions, and disclaims responsibility for any consequences resulting from  
the use of information included herein. Additionally, Silicon Laboratories assumes no responsibility for the functioning of undescribed features  
or parameters. Silicon Laboratories reserves the right to make changes without further notice. Silicon Laboratories makes no warranty, rep-  
resentation or guarantee regarding the suitability of its products for any particular purpose, nor does Silicon Laboratories assume any liability  
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation conse-  
quential or incidental damages. Silicon Laboratories products are not designed, intended, or authorized for use in applications intended to  
support or sustain life, or for any other application in which the failure of the Silicon Laboratories product could create a situation where per-  
sonal injury or death may occur. Should Buyer purchase or use Silicon Laboratories products for any such unintended or unauthorized ap-  
plication, Buyer shall indemnify and hold Silicon Laboratories harmless against all claims and damages.  
The sale of this product contains no licenses to Power-One’s intellectual property. Contact Power-One, Inc. for appropriate licenses.  
Silicon Laboratories and Silicon Labs are trademarks of Silicon Laboratories Inc.  
Other products or brandnames mentioned herein are trademarks or registered trademarks of their respective holders.  
8
Confidential Rev. 0.1  
 

Shindaiwa Trimmer X7502800900 User Manual
Snapper Snow Blower 7555 User Manual
Soleus Air Electric Heater HC4 15 20 User Manual
Soleus Air Fan MS 09 User Manual
Sony Cassette Player TC D5M User Manual
Sony CRT Television KV XJ29 User Manual
Sony Microphone ECM T15 User Manual
Sunbeam Food Processor LC6250 User Manual
T+A Elektroakustik Portable Speaker TCI 1 RE User Manual
Talkswitch Switch CTTS005002606 User Manual